close
Filter By
Connection Type
Length (ft)
6, 1, 4, 1/2 - 3 to 4
127 items
1/2" (16.5mm) Transair Female to 1/2" Male NPT Threaded Adapter
6605 17 22
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
1" (25mm) Transair Female to 3/4" Male NPT Threaded Adapter
6605 25 28
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
1" (25mm) Transair Female to 1" Male NPT Threaded Adapter
6605 25 35
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
1/2" (16.5mm) Union
6606 17 00
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- $20.18 20.18 USD
1" (25mm) Transair Female to 1/2" Male NPT Threaded Adapter w/ Fixing Plate
6615 25 22
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
1" (25mm) Transair Female to 3/4" Male NPT Threaded Stud Adapter w/ Fixing Plate
6615 25 28
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
1/2" (16.5mm) Vented End Cap
6625 17 00
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
1" (25mm) 3 Port Wall Bracket with ball valve w/ 1/2" Female NPT Threaded Ports
6638 25 22
Transair Wall Brackets make connecting machinery or tools to the supply line quick and easy. These brackets are rated for use in compressed air as well as industrial/inert gas applications. To match the needs/constraints of the environment, Parker offers a one (1), two (2), or three (3) port options. For extra control and safety over the media flow, we offer select wall brackets with an integrated ball valve. All wall brackets are equipped with a drain outlet for easy air or moisture drainage. The “full bore” design of Transair wall brackets paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All wall brackets are 100% recyclable, silicone free, and made from materials with no propagation of flame. All wall brackets conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2” to 4”: 232psi (15,9bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6”: 188psi (12,9 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature (1/2” to 4”): 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower
- USD
1/2" (16.5mm) 1 Port 45° Wall Bracket w/ 1/2" Female NPT Threaded Port
6640 17 22
Transair Wall Brackets make connecting machinery or tools to the supply line quick and easy. These brackets are rated for use in compressed air as well as industrial/inert gas applications. To match the needs/constraints of the environment, Parker offers a one (1), two (2), or three (3) port options. For extra control and safety over the media flow, we offer select wall brackets with an integrated ball valve. All wall brackets are equipped with a drain outlet for easy air or moisture drainage. The “full bore” design of Transair wall brackets paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All wall brackets are 100% recyclable, silicone free, and made from materials with no propagation of flame. All wall brackets conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2” to 4”: 232psi (15,9bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6”: 188psi (12,9 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature (1/2” to 4”): 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower
- USD