close
6, 1, 3 - Fittings & Valves
72 items
6" (168mm) to 4" (101mm) Reducing Tee
RA04 L8 L3
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
3" (76mm) Equal Cross
RA07 L1 00
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
3" (76mm) End Cap with 1/2" Port
RA25 L1 04
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
6" (168mm) End Cap with 1/2" Port
RA25 L8 04
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
3" (76mm) Equal Y
RA26 L1 00
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
6" (168mm) Equal Y
RA26 L8 00
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
8" (220mm) to 6" (168mm) ANSI Standard Aluminum Flange Reducer
RA31 L8 K2
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD
3" (76mm) Union w/ EPDM Seal
RR01 L1 01
Transair Fittings for Stainless Steel Pipe are quick and easy to install. All fittings are designed to securely fit around Transair stainless steel pipe, increasing system efficiency and preventing leaks. Transair fittings for stainless steel pipe are available in a variety of styles for easy assembly and layout design for compressed air, vacuum, industrial/inert gas, process water, or chemical transfer system. Fittings are available with either FKM or EPDM for robust chemical compatibility. The “full bore” design of Transair fittings pair with the low coefficient of friction in the stainless steel pipe ensures optimal flow throughout the system. All components are 100% recyclable, silicone free, and manufactured from materials with no propagation of flame. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 3/4" (22mm) and 1” (28mm) fittings use push-to-connect technology. To install, mark the insertion depth on the pipe and insert the pipe into the fitting until the edge of the connector meets the marked line on the pipe. Transair 1-1/2” (42mm) and 2” (60mm) fittings use clamp ring technology. To install, place the clamp ring over the lugs at the end of the pipe and slide the fitting nut in place. Next, hand tighten the nut onto the body. Lastly, use a pair of spanner wrenches to tighten the fitting one-half (1/2) turn. All 1-1/2” and 2” stainless steel pipe comes from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. Transair 3” (76mm) and 4” (101mm) fittings use clamshell technology. To install, place the remove cartridge over the end of the pipe until it meets the lugs. Next, place the clamshell union over the cartridge and tighten the fitting using a cross bolt pattern. All 3” and 4” stainless steel pipe comes from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our stainless steel catalog. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features/Benefits: Quick connection technology Modular and reusable Corrosion resistant Optimum flow rate 100% Recyclable Faster installation Lower installation costs Immediate Pressurization 10-year warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Process Water Chemical Transfer Maximum Working Pressure: 145psi (10bar) when the system is operated from +14 to +140F (-20 to +60C) 100psi (7bar) when the system is operated from +14 to +194F (-20 to +90C) Maximum Operating Temperature: +194F (+90C) when the system is operated with FKM seals and at 100psi (7bar) or lower
- USD
3" (76mm) Transair Male to 2-1/2" Male NPT Threaded Adapter for Aluminum Pipe
RR21 L1N20
Transair Fittings for Aluminum Pipe install fast and with minimal tooling. All Transair fittings are designed to securely fit around Transair aluminum pipe, increasing system efficiency and preventing compressed air leaks. Transair fittings come in a variety of styles for easy assembly and layout design of compressed air, vacuum, and industrial/inert gas systems. All Transair components can integrate into existing copper or steel systems, allowing for easy expansion of an existing system. The “full bore” design of Transair fittings, paired with the low coefficient of friction in the aluminum pipe ensures optimal flow throughout the compressed air system. All fittings are 100% recyclable, silicone free, and made from materials with no propagation of flame. All fittings conform to the UL94HB standard. Parker Hannifin warrants all Transair components to be free of defects in material and workmanship for 10 years from the date of installation. Transair 1/2” (16.5mm), 1” (25mm), and 1-1/2” (40mm) fittings use push-to-connect technology. All fittings ship from the factory pre-torqued and marked. To install, just push the pipe into the fitting until the insertion mark meets the end of the fitting. There is no need to tighten the nut of the fitting further. All 1/2” 1”, and 1-1/2”; pipes come from the factory with the insertion depth pre-marked, but if field cutting is required, the insertion depth needs to be marked using a Transair marking tool. Transair 2” (50mm) and 2-1/2” (63mm) fittings use snap ring technology. With a snap ring fitting, a polyamide retaining ring is inserted into 2 holes at the end of the pipe. This ring, along with tightening the fitting nuts with a spanner wrench, prevents the fitting from coming off the pipe. All 2”and 2-1/2” pipes come from the factory with the snap ring holes pre-drilled, but if field cutting is required, the snap rings holes need to be drilled using a Transair Drill Jig. Transair 3” (76mm), 4” (101mm), and 6” (168mm) fittings use clamshell technology. The clamshell fitting has a removable cartridge (seal) that fits over the end of the pipe and is prevented from sliding by the lugs on the end of the pipe. The fitting is then fitted over the lugs and the cartridge and bolted down using a cross pattern to prevent stripping the bolts. All 3” 4”, and 6” pipes come from the factory pre-lugged, but if field cutting is required, the lugs need to be made using a Transair lugging tool and die. For full installation instructions, download our installation manual, or watch our installation videos. Markets: Automotive Assembly Food and Beverage Packaging Industrial Plants Aerospace Features / Benefits: Quick connection technology Modular and reusable Corrosion resistant Full-bore design Optimum flow rate 100% recyclable Faster installation Lower installation costs Immediate pressurization Lightweight 10-year Warranty Applications: Compressed Air Vacuum Industrial/Inert Gases (i.e. Argon, Nitrogen, Carbon Dioxide) Maximum Working Pressure: 1/2”to 4”: 232psi (16 bar) when the system is operated between -4 to +113 F (-20 to +46.1 C) 6” to 8”: 188psi (13 bar) when the system is operated between -4 to +140 F (-20 to + 60 C) Maximum Working Temperature: 185°F when system is operated at 101psi or lower 158°F when the system is operated at 145psi or lower 140°F when the system is operated at 188psi or lower 115°F when the system is operated at 232psi or lower (1/2" to 4" Only)
- USD